**This does not fit a standard 5.25" CD-ROM drive bay (see below for links to that model).**
I created these slimline carriers allow easy access to compact flash and SD cards. They are approximately 1 1/8" tall, a size used in some Compaq systems. See my other sales for a standard 5.25" drive bay carrier. You have a choice between 1 or 2 slot compact flash to IDE, SD to IDE, mSD to IDE and a carrier only option for Startech compact flash to IDE boards.
The single slot CF to IDE boards can operate as either a master or slave device, selectable via a jumper on the board. The board is powered by a floppy power connector (cables and flash card are not included). You can attached other devices to the IDE cable as needed.
The dual slot CF to IDE board is seen by the PC as two drives (primary and secondary). When using two drives it should be installed on the end of the IDE cable. When the jumper is on pins 1 and 2 the top card slot is the master and the bottom card is the slave. When the jumper is on pins 2 and 3 the top card is the slave and the bottom card is the master. No other device can be on the IDE cable when using dual CF card readers (as the card it seen as two IDE devices). If you only want to use one CF card on the dual readers you can move the card to the secondary IDE port on the cable and use the top slot. The jumper should be on pins 2 and 3 (this effectively makes the dual slot CF to IDE board a single slot CF to IDE board).
All cards are inserted with the label facing up.
You can add on a 4 pin Molex to floppy power connector to your order. This is especially handy in tight cases where it would be challenging to get the power cable to the IDE board.
Features/Specs:40 or 80 pin standard male IDE connectorMaster or slave mode selection on CF card readersSingle or dual 50-Pin standard compact flash socket
The SD and microSD to IDE card readers only work as the master device on each IDE cable. You can attach a slave device without any issues.
The carriers have holes that align in the typical CD-ROM / floppy drive configuration on the sides and bottom. You can power the SD to IDE adapter board with either the floppy power connector or the hard drive Molex connector, (as noted above, the CF/2CF boards are powered by a floppy Molex connector).
Reach out if you'd like another color; if I can obtain the filament I can print it. Let me know if there is another style you are looking for, I can customize the carriers (e.g. SD card reader and compact flash). I can desolder the LEDs on the boards if you would like them to remain dark inside your case.
Fast Priority Mail shipping from Connecticut.
For standard 5.25" drive bays (like a CD-ROM drive):5.25" (40 pin) SD to IDE carrier or adapter with carrier: (40-pin) Syba/StarTech: (40 pin) CF to IDE carrier + adapter: out my other sales if you are looking for other options, including:
SD to IDE2.5" (44 pin) SD to IDE adapter, carrier, or adapter with carrier: (40 pin) SD to IDE adapter, carrier, or adapter with carrier: 5155 (40 pin) SD to IDE carrier or adapter with carrier: bracket for 3.5" SD to IDE (40 pin) adapter: bracket with 3.5" SD to IDE (40 pin) adapter: to SATA3.5" SD to SATA carrier: bracket for 3.5" SD to SATA adapter: to IDE3.5" (40 pin) microSD to IDE adapter, carrier, PCI bracket with adapter, or adapter with carrier: bracket for 3.5" (40 pin) microSD to IDE adapter: to IDE board: flash to IDE3.5" (40 pin) Single or Dual CF to IDE adapter with carrier: bracket with Single or Dual 3.5" CF to IDE (40 pin): to PATA5.25" drive bay for 2.5" SATA drives to PATA / IDE: / 5.25" Floppy Disk feet for IBM 5151/5153/5154 me know if there is another style or component you are looking for, I can create custom parts. Thanks!