2-piece Hartk Stealthburner Toolhead PCB by LDO Motors This comes completely assembled with no need for soldering anything on the PCB. This is the board that is included with newer LDO Trident and V2.4 kits The second PCB plugs into the main PCB, specifically made to connect your 4010/5015 fan and LEDs by soldering to the PCB. It is intended as an additional convenience piece. The Stealthburner PCB is based on hartk's two piece toolhead PCB design. The design consists of: The main toolhead PCB - which installs into the wiring enclose in the side of the Clockwork 2 extruder. The fan adapter PCB - which installs onto the back of the 5015 fan in the Stealthburner main body. While the LDO stealthburner PCB uses the same PCB outline as the hartk's design, it uses a different circuit design. The LDO version is designed to be completely compatible with the original LDO breakout PCB (see below) while requiring only a small number of cable modifications for those upgrading from the old LDO afterburner PCB. Pinout: Main Toolhead PCB The table below briefly describes the purpose of each port located on the toolhead PCB. PCB Label Name Connector Description HE0 Hotend Heater E0508 Ferrule Port for hotend heater cartridge. TH0 Hotend Thermistor JST-XH-2P Thermistor port for hotend XES X Endstop JST-XH-2P X endstop port. Only used in Switchwire builds, unused in V2 and Trident. PROBE Probe JST-XH-3P Probe port. Accepts 24V inductive probes, also compatible with klicky probes. E-STEP E Stepper Motor JST-XH-4P Extruder stepper motor port CT Chamber Thermistor JST-XH-2P Connects to an external thermistor for more accurate chamber temperature readings. Fan Adapter Header 2x8 M-Header Plugs into the female header on the Fan Adapter PCB Toolhead Cable Microfit3-14P This port connects to the 14pin toolhead cable. Neopixel Cable Microfit3-2P This port connects to the 2pin neopixel cable. Pinout: Fan Adapter PCB The table below briefly describes the purpose of each port located on the toolhead PCB. PCB Label Name Connector Description HEF+/A1/HEF- Hotend Fan* JST-PH-3P Fan port for cooling the hotend heatsink. 24V/5V selectable, defaults to 24V. PCF+/A2/PCF- Part Cooling Fan* JST-PH-3P Port for part cooling fan. 24V/5V selectable, defaults to 24V. 5V/GND/LED Neopixel JST-PH-3P For connecting to the neopixel chain on the stealthburner. Toolhead Cable 2x8 F-Header Plugs into the male header on the main toolhead PCB *The hotend fan and part fan can be independently changed to 5V in two steps: Severe the 24V connection by cutting the trace between the 24V pad and V_HEF/V_PCF pad Make a soldered bridge connection between the 5V pad and V_HEF/V_PCF pad More information can be found here. 2-piece Hartk Stealthburner Toolhead PCB by LDO Motors
This comes completely assembled with no need for soldering anything on the PCB. This is the board that is included with newer LDO Trident and V2.4 kits
The second PCB plugs into the main PCB, specifically made to connect your 4010/5015 fan and LEDs by soldering to the PCB. It is intended as an additional convenience piece.
The Stealthburner PCB is based on hartk's two piece toolhead PCB design. The design consists of:
- The main toolhead PCB - which installs into the wiring enclose in the side of the Clockwork 2 extruder.
- The fan adapter PCB - which installs onto the back of the 5015 fan in the Stealthburner main body.
While the LDO stealthburner PCB uses the same PCB outline as the hartk's design, it uses a different circuit design. The LDO version is designed to be completely compatible with the original LDO breakout PCB (see below) while requiring only a small number of cable modifications for those upgrading from the old LDO afterburner PCB.
Pinout: Main Toolhead PCB
The table below briefly describes the purpose of each port located on the toolhead PCB.
PCB LabelNameConnectorDescriptionHE0Hotend HeaterE0508 FerrulePort for hotend heater cartridge.TH0Hotend ThermistorJST-XH-2PThermistor port for hotendXESX EndstopJST-XH-2PX endstop port. Only uséd in Switchwire builds, unuséd in V2 and Trident.PROBEProbeJST-XH-3PProbe port. Accepts 24V inductive probes, also compatible with klicky probes.E-STEPE Stepper MotorJST-XH-4PExtruder stepper motor portCTChamber ThermistorJST-XH-2PConnects to an external thermistor for more accurate chamber temperature readings. Fan Adapter Header2x8 M-HeaderPlugs into the female header on the Fan Adapter PCB Toolhead CableMicrofit3-14PThis port connects to the 14pin toolhead cable. Neopixel CableMicrofit3-2PThis port connects to the 2pin neopixel cable. Pinout: Fan Adapter PCB
The table below briefly describes the purpose of each port located on the toolhead PCB.
PCB Fan*JST-PH-3PFan port for cooling the hotend heatsink. 24V/5V selectable, defaults to 24V.PCF+/A2/PCF-Part Cooling Fan*JST-PH-3PPort for part cooling fan. 24V/5V selectable, defaults to 24V.5V/GND/LEDNeopixelJST-PH-3PFor connecting to the neopixel chain on the stealthburner. Toolhead Cable2x8 F-HeaderPlugs into the male header on the main toolhead PCB
*The hotend fan and part fan can be independently changed to 5V in two steps:
- Severe the 24V connection by cutting the trace between the 24V pad and V_HEF/V_PCF pad
- Make a soldered bridge connection between the 5V pad and V_HEF/V_PCF pad
More information can be found here.
×
Buy now and save! Shipping info
Click the Shipping & Payments tab above the listing description for more info
Click the Shipping & Payments tab above the listing description for more info!
Additional delivery notes
PICK UP OPTION
Our items are available for pick-up. Pick up procedure is as follows:
- Purchase the item through
- Email us to coordinate pickup
PAYMENT
Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.
We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.
We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).
The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.
Thank you for shopping with us on !
Additional Information
No additional information at this time
Ask seller a question
You might also like AMBROSIA Über ABS Filament of the Gods - 1KG Bambu AMS Friendly Cardboard Spools AMBROSIA ASA Galactic Filament of the Gods (Glitter / Sparkle) - 1KG Bambu AMS F AMBROSIA PETG Filament of the Gods - 1KG Bambu AMS Friendly Cardboard Spools Pre AMBROSIA PLA Filament of the Gods - 1KG Bambu AMS Friendly Cardboard Spools Prem Contact
To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.
Ask seller a question
© West3D Printing
Shipping & Payments
Click the Shipping & Payments tab above the listing description for more info
Payment
Accepted Payment Methods
Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.
We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.
We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).
The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.
Thank you for shopping with us on !
Returns
Returns are accepted
Items must be returned within 30 days of the sale ending
Seller will pay for return shipping.
integration by
