This listing is for the Odroid N2+ 2gb ram with power supply included!
ODROID N2+ is a new generation single board computer that is more powerful, more stable, and faster performing than N1. The main CPU of the N2+ is based on big.Little architecture which integrates a quad-core ARM Cortex-A73 2.4Ghz CPU cluster and a dual core Cortex-A53 2.0Ghz cluster with a new generation Mali-G52 GPU. Thanks to the modern 12nm silicon technology, the A73 cores runs at 2.4Ghz without thermal throttling using the stock metal-housing heatsink allowing a robust and quiet computer.
On-board RTC backup battery holder is mounted on the board.
The main CPU is based on big.Little architecture which integrates a quad-core ARM Cortex-A73 CPU cluster and a dual core Cortex-A53 cluster with a new generation Mali-G52 GPU.
Thanks to the modern 12nm silicon technology, the A73 cores run at 2.2Ghz without thermal throttling using the stock metal-housing heatsink allowing a robust and quiet computer.
The CPU multi-core performance is around 20% faster and the GPU is 10% faster than the N1. The N2+’s DDR4 RAM is running at 1320Mhz with 1.2volt low power consumption.
The large metal housing heatsink is designed to optimize the CPU and RAM heat dissipation and minimize throttling. The CPU is placed on the bottom side of the PCB to establish great thermal characteristics.
Here is an example of emulator running on the n2+. The speed is just amazing!
Dolphin Emulator Test On ODROID N2+ Android Vulkan Driver
Using the mobile app? Copy this link into your browser:
SBC Specification
Form FactorBoard Dimensions: 90mm x 90mm x 17mm
Heatsink Dimensions: 100mm x 91mm x18.75mm
Weight:200g including heatsink
ProcessorAmlogic S922X Processor (12nm fab)
Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G52 GPU with 6 x Execution Engines (800Mhz)
MemoryDDR4 4GiB or 2GiB with 32-bit bus width (this is the 2GB version)
Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design
Storage1 x eMMC connector (8G, 16G, 32G, 64G and 128G are available)
1 x microSD slot (DS/HS modes up to UHS-I SDR104)
Networking1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
– Realtek RTL8211F (Ethernet transceiver)
– LED indicators
* Green LED: Flashing by data traffics at 100Mbps connection
* Amber LED: Flashing by data traffics at 1000Mbps connection
Optional WiFi USB adapters
Video1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
1 x Composite video (3.5mm jack)
Audio1 x Stereo Audio line-out (3.5mm jack)
1 x HDMI digital output
1 x Optional SPDIF optical output
External I/O4 x USB 3.0 Host ports (shares one single root hub)
1 x USB 2.0 OTG port for Host or Device mode. (No power input)
1 x Debug serial console (UART)
1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)
– 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND
– 1 x SPI
– 1 x UART
– 2 x I2C
– 25 x GPIO (Max)
– 2 x ADC input (10bit, 1.8V Max)
– All 3.3V I/O signal level except for ADC input at max 1.8Volt.
Other featuresOn board RTC(Real Time Clock) IC to keep date and time. A CR2032 coin battery holder was replaced with the 2-pin 1.25mm pitch connector.
No battery is included in the board.
Please purchase the very common bare CR2032 cell from your local store.
You can keep the RTC time up to several years with a 200mAh CR2032 battery.
8MiB SPI Flash for boot manager
IR receiver for remote controller
Built with a large passive heatsink
System LEDS Indicators:
– Red (PWR) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
Active Cooling Fan Connector (5V 2-pin)
– Connector (2-pin, 1.25mm pitch)
Power1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
DC 7.5V ~ 18V (up to 25W)
– DC 12V/2A power adaptor is recommended
Power consumption:
– IDLE : ≃ 2.2W (Performance governor)
– CPU Stress : ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz)
– Power-off : ≃ 0.2W
